This post down below about How to Install a Bathtub is totally entertaining. Don't bypass it.
Setting up a bathtub isn't precisely brain surgery, but it does need solid plumbing, woodworking, and sometimes, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily available, the project can move speedily; if you have to open a wall surface to remove the old tub and place the new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. See to it you have certified yourself for the work as well as fit trying it. Instead of working with a service provider to take over a halfway-completed task, it is much better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your devices and also material list should make up the following:
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, activate the taps to drain any water staying in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and adjusting the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints and brand-new pipework for leaks as well as tighten them if essential. Fill up the bath tub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Protect the tap in place with the producer given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous type should be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, creating the water to permeate the wall between the bath and the tiling, causing problems with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealant can split fairly very early if you do not take into consideration this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly available on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that editorial on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a good friend on a different web page. Do you know somebody else who is very much interested in the subject? Be sure promote it. Thank you for your time. Come back soon.
Schedule Free Estimate